Arturia Forums
Hardware Instruments => PolyBrute => PolyBrute - General discussions => Topic started by: dave the butcher on March 18, 2021, 11:08:17 am
-
Hi everyone,
I just made a Cheat Sheet to remember all (non-standard-[settings]) shortcuts. 8) It might be incomplete, but a good starting point for your own cheat sheet. The docx is attached.
If you have additions, please post here.
greets
Dave
Shortcut Function
[Panel left arrow] + [Preset] Initialize Patch
Hold LFO [Mode]/[Retrig] for 1 second LFO Polarity
Hold LFO [Sync] Division Menu
[Panel left arrow] + Master Cutoff Reset Master Cutoff
[Settings] + Attack/Decay Envelope curves
[Settings] + Velo slider envelope's velocity modes
[Settings] + Stereo knob: Voice pan / Voice + Filter pan
[Settings] + Morphée surface /
Morphée button 1 second. Morphée Settings page
[Polyphony] + key, number of voices used by each zone
[Timbrality] + key split point
[Timbrality] + [Octave < / >] transpose lower half
Hold [Wheel] button Vibrato Options
[Settings] + Morphée surface /
Morphée button 1 second. Morph response
[Save] once Snapshot
[Settings] + [Save] recall a Snapshot
[Save] three times save to current location
[Save] + [Assign 1-8] (optional) +Press Matrix A1-L8 Save preset to other location
[Panel left arrow] + Amount Knob Reset Mod Level to 0
[Panel left arrow] + Mods button. clear the Modulation Matrix,
[Panel left arrow] + Assign Button Delete Mod Destination
Sequencer
[Metro] for 1 second. count-in feature
[Tap] button in rec mode playing erase notes
Hold [Sequencer] Sequence editing features
[Seq] + Rate Tempo in 0.1 Increments
[Stop] 3 times All Notes Off Command
-
thank you :)
-
:)
-
The best one - hold presets and turn any knob or slider and it will show you where the value for it is set.
-
Cool, thx
-
The best one - hold presets and turn any knob or slider and it will show you where the value for it is set.
wow. thank you. but do you know why always the A & B parameters are changed simultanously?
-
The best one - hold presets and turn any knob or slider and it will show you where the value for it is set.
wow. thank you. but do you know why always the A & B parameters are changed simultanously?
It just displays A and B values, no changes made.
-
Hi all,
With the new firmware version 2 I thought I'd revisit this thread and update the original list from "dave the butcher". My list only deals with voice programming related shortcuts. Here's the raw version of the data and I've attached a *.doc version for anyone who'd like to d'load and make their own additions. It would be great if people could post any shortcuts they know of that aren't already on both Dave's original list and my updated one!
Thanks ;)
Shortcut Function
[Panel left arrow] + [Preset] Initialize Patch
[Panel left arrow] + Master Cutoff Reset Master Cutoff
[Panel left arrow] + Amount Knob Reset Mod Level to 0
[Panel left arrow] + Mods button. clear the Modulation Matrix,
[Panel left arrow] + Assign Button Delete Mod Destination
[Settings] + Morphée Controller Morphée Settings: Tap/Hold/Scan/HoldScan
[Settings] + Morph Knob Morph Pitch Quantize: Continuous/Chromatic/Intervals
[Settings] + VCF/VCA/MOD Attack/Decay Set Attack: Default/Quick & Decay: Default/Percussive
[Settings] + VCF/VCA Velo slider Env Mode: Amt/Net/Short/Extend/Single/x2/x3/Loop
[Settings] + Mod Env Delay Env Loop Mode: Single/x2/x3/Loop
[Settings] + Stereo knob: Voice pan /Voice + Filter pan, Distribution: Centered/Gradual
[Settings] + VCO1 Tune Tune Modulation Intervals
[Settings] + VCO2 Tune Tune Knob & Modulation Intervals
[Settings] + VCO1 Metalizer Mode: Triangle or ALL waves
[Settings] + VCO2 Sub Sub Level Crossfade or Level
[Settings] + LFO3 Curve Rise: Standard/Inverted
[Settings] + Fine Tune Analog Accuracy Pitch/Others: Off/Mild/Medium/Wild
[Settings] + Modulation Intensity EQ Presets: Bypass/7 Other Presets
[Settings] + Delay Time Time Modes: Hz/Sync-Bi/Sync-Tri/Sync-Dotted
[Settings] + Delay Type Delay 7 Additional Presets
[Settings] + Delay Regeneration Delay Filters: 4 HP & 4 LP choices
[Settings] + Reverb Damping Reverb HP Filters: Bypass/Lo/Mid/Hi Cutoffs
[HOLD] Morphée Button Morphée Settings: Tap/Hold/Scan/HoldScan
[HOLD] Wheel Button Vibrato Options: Range & Source
[HOLD] LFO1/LFO2 Mode Global Retrig: Mono:On/Off, Polarity:Unipolar/Bipolar
[HOLD] LFO3 Retrig LFO3 Polarity: Unipolar/Bipolar
[HOLD] LFO1/LFO2/LFO3 [Sync] Divisions: Binary/Triplet/Dotted
[HOLD] Polyphony Button [Uni/Mono] Uni/Mono Allocation: Priority/Legato
[HOLD] Polyphony Button [Poly] Poly Allocation: Note & Steal Options
[HOLD] Timbrality Button Polyphonic Allocation (Lower)
[Settings] + [Save] Recall a Snapshot
[Save] three times Save to current location
[Save] + [Assign 1-8] +Press Matrix A1-L8 Save preset to other location
-
I will be making use of both lists. Thank you!
-
;)
-
Nice!
I have one issue though: "Seq + Rate" for internal tempo doesn't seem to work (v2.0). I have set it to Internal Clock.
Setting the tempo inside Polybrute Connect VST works though.
-
Dear all - I have added some additional shortcuts....
This includes Debug Mode, where "holding Polyphony" in Debug Mode displays information to each Note and its individual Source, Upper/Lower, Velocity Strength.
Good for analysing Note Steal issues, or quirky voices in some settings (sometimes single voices are overreacting with the Brute Factor - one cannot really do anything against it, but at least knows....)