March 28, 2024, 02:39:13 pm
Welcome, Guest. Please login or register
News:

Arturia Forums



Author Topic: Control voltage input specs?  (Read 10663 times)

leighmarble

  • Apprentice
  • Apprentice
  • *
  • Posts: 10
  • Karma: 0
Control voltage input specs?
« on: March 01, 2013, 08:40:20 pm »
Hello,

Is there anywhere that the Minibrute's Control Voltage input specs have been published? I've looked, but can't find this info anywhere.

I'd guess that the Pitch input takes a 0-10V range (1 V/oct). However, what about the Filter and Amp CV inputs? Same range?

Also, do negative CV values get added to the internal values, or are negative values ignored?

thanks,
Leigh
« Last Edit: March 20, 2013, 03:10:50 pm by David@Arturia »

tertior

  • Full Member
  • ***
  • Posts: 169
  • Karma: 7
Re: Control voltage input specs?
« Reply #1 on: March 03, 2013, 03:20:33 pm »
Re: Arturia MiniBrute (monophonic analog synth)[/size]de yusynth[/size][/b] » 02 Mar 2013, 15:17[/font][/size]
C'est du 0-10V mais cela accepte aussi des tensions négatives jusqu'à -5V.
It's of Anafrog Forum ( http://forum.anafrog.com/phpBB/viewtopic.php?f=26&t=6151&start=2460 )[/font][/color]

leighmarble

  • Apprentice
  • Apprentice
  • *
  • Posts: 10
  • Karma: 0
Re: Control voltage input specs?
« Reply #2 on: March 03, 2013, 06:58:47 pm »
Thank you for finding that information, tertior.

So, the final answer (from Yves himself): the CV input range is from -5 to 10V.

The way he said it was "0-10V but it also accepts negative voltages up to 5V", so that sounds right, unless he was hinting that negative range is treated somehow differently...

cheers,
Leigh

beefinator

  • Full Member
  • ***
  • Posts: 149
  • Karma: 4
    • Soundcloud page
Re: Control voltage input specs?
« Reply #3 on: March 03, 2013, 08:39:19 pm »
Maybe he's just saying that the negative voltages might not work as expected, but will not damage the device.

yusynth

  • Apprentice
  • Apprentice
  • *
  • Posts: 45
  • Karma: 26
Re: Control voltage input specs?
« Reply #4 on: March 13, 2013, 07:56:46 am »
By this I meant, that the normal range is 0 to 10V but using voltages down to -5V will work too, for example the VCO will run like a very slow LFO, or the filter in LP mode will mute all sounds. A negative voltage (limited to -5V) will not harm your MiniBrute.

leighmarble

  • Apprentice
  • Apprentice
  • *
  • Posts: 10
  • Karma: 0
Re: Control voltage input specs?
« Reply #5 on: March 13, 2013, 09:19:11 pm »
Thank you for the precise answer, Yves!

Is the Gate input also 0-10V? I recently built a Trigger Converter circuit, using this schematic, which has a V-trigger output at 12V. I'm pretty sure that's not going to break anything, but just wondering what the ideal gate voltage would be for the Minibrute.

cheers,
Leigh


yusynth

  • Apprentice
  • Apprentice
  • *
  • Posts: 45
  • Karma: 26
Re: Control voltage input specs?
« Reply #6 on: March 13, 2013, 09:36:39 pm »
Thank you for the precise answer, Yves!

Is the Gate input also 0-10V? I recently built a Trigger Converter circuit, using this schematic, which has a V-trigger output at 12V. I'm pretty sure that's not going to break anything, but just wondering what the ideal gate voltage would be for the Minibrute.

cheers,
Leigh

The MiniBrute expects 0/5V GATE signal but I think it can handle 0/12V too but this has to be confirmed by Bruno though...

Bruno@arturia

  • Global Moderator
  • Hero Member
  • *****
  • Posts: 501
  • Karma: 34
Re: Control voltage input specs?
« Reply #7 on: March 14, 2013, 02:42:01 pm »
indeed 0/12V will be fine.
« Last Edit: March 20, 2013, 03:10:53 pm by David@Arturia »
Bruno
Arturia Hardware

Miltiadis

  • Newbie
  • *
  • Posts: 1
  • Karma: 0
Re: Control voltage input specs?
« Reply #8 on: April 25, 2017, 07:33:06 pm »
Sorry for resurrecting  this old topic but I'd like to ask if 5 volts are enough to trigger microbrute envelopes through gate in
Thanx in advance!

Bruno@arturia

  • Global Moderator
  • Hero Member
  • *****
  • Posts: 501
  • Karma: 34
Re: Control voltage input specs?
« Reply #9 on: May 18, 2017, 10:34:15 am »
Yes 5V is enough on MiniBrute, MicroBrute and MatrixBrute
Bruno
Arturia Hardware

 

Carbonate design by Bloc
SMF 2.0.17 | SMF © 2019, Simple Machines